Complete Application Tutorial for MTxRUWSL Series Programmable Motorized Turntable

1. Unboxing and Basic Power-on Preparation

Point 1: Accessories Check

Before powering on the MTxRUWSL series programmable motorized turntable, fully check all matched standard accessories. The complete package includes turntable main body, dedicated power adapter, USB data cable, infrared remote controller, factory-attached camera shutter cable and shutter extension cord. All shooting matching accessories are provided by default. Check all parts for breakage, missing items or surface damage before assembly and power connection. This series integrates built-in shutter signal output hardware to support automatic synchronous shooting.For a full product overview, visit the official MTxRUWSL product page.

Point 2: Standard Power-on Step-by-Step Operation

• Step 1 Take out the original power adapter, insert the DC round plug into the dedicated power jack on the  MTxRUWSL turntable side;
• Step 2 Plug the AC two-hole plug of the adapter into standard household alternating current socket;
• Step 3 Toggle the power switch on turntable side from OFF to ON gear, the device enters standby state immediately after power supply, ready for all supported control modes including automatic shooting and automatic zero return origin function.This programmable motorized turntable supports three independent control methods, which we will cover in detail below.

Point 3: Power-on Environment & Hardware Usage Rules

• First, only deploy the factory-provided matching power adapter, third-party power supplies with mismatched voltage will damage internal drive and shutter control components of your programmable turntable;
• Second, place the turntable on horizontal, solid flat desktop without tilt to eliminate shaking during rotation;
• Third, avoid long-term placement in damp, high temperature, oily and dusty work environments to prevent internal circuit corrosion and motor jamming.
• The reserved 3.5mm shutter port on the turntable side works with the factory-supplied shutter wires to realize automatic camera shooting linkage under all rotation modes.

2. Detailed Step-by-Step Operation of Three Available Control Modes

2.1 Infrared Remote Control Operation

Point 1 One-Click Adjustment of Basic Rotation Parameters

After the MTxRUWSL turntable enters standby, pick up the infrared remote controller equipped with two AAA batteries. The left and right arrow keys switch clockwise or counter-clockwise rotation direction; the speed up/down keys adjust rotation speed in real time within the full speed range; numerical shortcut keys of 0.1°,1°,5°,10°,12°,15°,18°,36°,45°,90°,180°,360° can directly set single-step rotation angle. The remote panel is equipped with independent Focus, Shutter and AF+Shutter dedicated buttons for one-click manual camera trigger.

Point 2 Permanent Saving of Running Parameters

After adjusting rotation direction, speed, step angle, cycle mode, and auto-shoot switch via remote buttons, press the dedicated Save button on the remote panel. All current configuration data (including automatic shooting enable/disable status) will be written into the MTxRUWSL turntable’s built-in flash storage chip. After complete power-off and restart, rotation and shutter trigger parameters will automatically load without repeated adjustment. This programmable motorized turntable ensures your settings persist across sessions.

Point 3 Remote Function Boundary Description

All core rotation, zero positioning and manual shutter switching operations can be finished by remote, but the remote hardware cannot edit custom pause time of intermittent step rotation. To modify accurate pause interval and auto-shoot delay seconds, users must connect Windows TurntableX software for parameter editing.

2.2 Windows TurntableX Software Control

Point 1 Full USB Wired Connection Process

• Visit the official website to download the CH340 USB-to-serial driver compressed package. Extract files and run the Install program to complete driver installation. You can download the driver directly from the ComXim software download center.
• Use standard USB Type-B data cable to connect turntable side USB port and computer USB interface;
• Open Windows Device Manager, expand Ports column to check the generated USB-SERIAL CH340 COM serial number;
• Launch TurntableX software, select the corresponding COM port from the dropdown menu, and click Connect. A double-headed arrow icon appears to indicate successful wired connection. The software includes fully editable shutter parameter modules compatible with the factory-provided shutter cable set. This programmable turntable tutorial recommends using the USB connection for first-time configuration.

Point 2 Full WiFi Wireless Connection Process

• Power on the MTxRUWSL programmable turntable and wait 10 seconds for built-in WiFi AP hotspot to activate, the hotspot name is consistent with MTxRUWSL series model;
• Open computer WLAN list, find the matching hotspot and input default password 88889999 to finish network connection (the hotspot only provides device control signal without internet access);
• Open TurntableX software, switch connection mode to IPv4, the fixed turntable IP address 192.168.181.181 is pre-filled, directly click Connect to establish wireless control. WiFi communication transmits both rotation control and auto-shoot CT commands synchronously.

Point 3 Exclusive Refined Shutter & Rotation Parameter Configuration Function

TurntableX covers all remote control functions and adds exclusive adjustable parameters unavailable on the remote: customizable pause time, auto-shoot trigger delay, independent setting of total cycle times, one-click enable/disable automatic shutter output, and one-click disable infrared remote lock function. Users can read the unique device EBC hardware serial number through the software device query window for equipment identification management. The software provides separate test buttons to manually trigger camera shooting via factory shutter wires. Following this turntable tutorial will help you leverage all these advanced features.

2.3 Android TurntablePlus WiFi APP Control

Point 1 APP Download & Installation Steps

• Visit official software resource webpage via computer browser, download TurntablePlus.zip compressed file containing APK installation package;
• Transfer the APK file to Android mobile storage via USB data cable;
• Turn on mobile permission of installing unknown applications, click the APK file to finish APP installation.

Point 2 Full Mobile WiFi Pairing & Device Connection Process

• Power on the MTxRUWSL turntable, wait for WiFi hotspot broadcast;
• Open mobile WLAN settings, scan available networks and select the series-named turntable hotspot, input password 88889999 to connect;
• Launch TurntablePlus APP, the fixed IP 192.168.181.181 is preset in the input box, tap Connect button at the top of the page to complete mobile-device communication connection.

Point 3 All Adjustable Rotation Parameter Operations Inside APP

After successful connection, users can freely switch five built-in rotation modes, adjust rotation angle, speed, pause time and auto-shoot switch status, set total repeated cycles, save parameter schemes locally. The automatic shooting signal will be output through the factory-attached shutter cable during segment pause periods.

3. Full Detailed CT Command Secondary Development Process

Point 1 Pre-development Basic Preparation

• Download official full CT command manual document, which records rotation, zero positioning and dedicated auto-shoot trigger instructions, complete parameter formats and device feedback rules.Access the CT command reference guide for detailed documentation.;
• Prepare development terminal equipment: Windows/Linux/macOS computer or Android industrial control device;
• Select communication channel: USB serial port (CH340 COM) or WiFi TCP socket connection, Bluetooth communication is not supported;
• Complete turntable hardware power-on and shutter cable wiring, then finish wired/wireless connection as per the operation guides. This programmable turntable tutorial includes development guidance for advanced users.

Point 2 Step-by-Step Implementation of USB Serial Communication Development

• Complete CH340 driver installation, confirm COM port number via system port manager;
• Import serial communication library, configure baud rate 115200, data bit 8, stop bit 1, parity none;
• Write serial port connection code to build two-way data transmission channel;
• Encode rotation, origin and auto-shoot logic into standard CT strings for serial transmission;
• Set receiving thread to capture pause, shooting trigger and full-circle completion feedback signals;
• Write Save command code to store rotation and shutter parameters into turntable flash permanently.

Point 3 Step-by-Step WiFi TCP Socket Development

• Connect development device to MTxRUWSL turntable WiFi hotspot with password 88889999;
• Create TCP Client socket program, target IP 192.168.181, port 8181;
• Establish persistent TCP long connection;
• Transmit auto-shoot enable/disable and rotation CT commands via TCP data packets;
• Develop data parsing module to resolve shooting completion event feedback uploaded by turntable;
• Add EBC reading command for equipment batch management and copyright binding.

Point 4 Practical Common CT Command Cases (Auto-Shoot Dedicated Instructions Included)

• Case1 Single-step rotation: CT+TURNSINGLE(30,1); rotate counter-clockwise 30° and stop;
• Case2 Repeated auto-shoot cycle: CT+START(0,2,5,4,10); clockwise 5° per step, pause 4s, auto shutter triggered at pause midpoint, 10 total cycles;
• Case3 Set hardware origin: CT+SETO; lock current position as permanent zero;
• Case4 Return origin: CT+RETO; shortest path auto homing;
• Case5 Save all rotation & shutter config: CT+SAVE; write parameters to flash;
• Case6 Auto shutter switch: CT+SHUTTER(1); enable automatic shooting output (1=on,0=off).

Point 5 Adaptable Industry Scenarios for Development

Unified CT command system supports customized automation programs, especially for e-commerce product 360° photography, 3D model scanning with automatic shooting requirements, also applicable to static display, industrial inspection and laboratory positioning with optional auto-shoot function, matched with factory-supplied shutter wire set for DSLR linkage.This programmable motorized turntable adapts to diverse professional environments.

4. Step-by-Step Operation Tutorial for Five Built-in Rotation Modes

All five rotation modes built into the MTxRUWSL series programmable rotating platform support independent adjustment of rotation speed and clockwise/counter-clockwise direction. Users can switch to any other mode at any time during running status, the turntable will immediately execute new parameter rules after mode switch.

4.1 Continuous Rotation Mode

Point 1 Applicable Scenarios

Applicable to long-time static commodity exhibition, live broadcast continuous rotating display, long-cycle uniform rotation test of industrial samples, no fixed pause interval required during operation.

Point 2 Full Operation Steps

• Use remote/TurntableX/TurntablePlus to select Continuous Rotation Mode;
• Adjust rotation speed slider or speed plus/minus keys to set target rotational speed;
• Tap clockwise or counter-clockwise direction option;
• Click Start button, turntable runs at constant speed;
• Click Stop button or switch other modes to terminate rotation at any time.

4.2 Single-Step Mode

Point 1 Applicable Scenarios

Used for precise hardware zero calibration, single fixed-angle sample shooting positioning, small-range position adjustment of displayed goods, only one rotation action will be executed each startup.

Point 2 Full Operation Steps

• Activate Single-Step Mode on control terminal;
• Input target rotation angle value via numerical shortcut or parameter input box;
• Set rotation speed and rotation direction;
• Press Start key, turntable rotates to designated angle then automatically locks and stays static without extra movement.

4.3 Repeated Step Mode

Point 1 Applicable Scenarios

Suitable for intermittent cyclic display of handicrafts, repeated fixed-angle industrial detection, regular positioning check of experimental samples, with customizable static pause between each rotation segment.

Point 2 Full Operation Steps

• Select Repeated Step Mode on control device;
• Fill in single rotation angle, custom pause duration seconds, rotation speed and direction;
• Set total repeated cycle times or unlimited loop mode;
• Click Start; turntable rotates set angle → hold static for set seconds → repeat the whole cycle continuously until Stop command is triggered. Default pause base value is 4 seconds, adjustable via software/APP.

4.4 Pendulum (Swing) Mode

Point 1 Applicable Scenarios

For dynamic reciprocating display of ornaments, reciprocating angle detection of mechanical parts, back-and-forth swing presentation of exhibition products, the turntable takes current position as swing center point.

Point 2 Full Operation Steps

• Switch to Pendulum Swing Mode;
• Set maximum swing angle range and rotation speed;
• Tap Start button; turntable swings to the set angle to left side, pause briefly, reverse direction to swing equal angle to right side, pause again, cycle back and forth continuously until stopped manually.

4.5 Multi-step Within One Circle Mode

Point 1 Applicable Scenarios

Applicable to full-circle uniform positioning for 3D scanning equipment, all-angle static product display without photography, full-circle regular industrial sampling detection.

Point 2 Full Operation Steps

• Choose Multi-step Within One Circle Mode;
• Select segment quantity via remote shortcut keys (2/4/8/16/18/24/32/36/48/50/60/64/72/96/120/144 optional) or input custom number in software/APP;
• Configure rotation speed and pause duration after each segment rotation;
• Start the mode, turntable rotates 360/n degrees each segment, pause after every movement, automatically stop after completing full 360-degree cycle.

Point 3 Shutter Cable Usage Instruction

When connecting a DSLR camera, first connect the turntable 3.5mm shutter port with the shutter extension cord, then plug the camera dedicated shutter cable to the other end of the extension line for lengthened wiring range during shooting layout. Both wires are delivered with the turntable out of the box, no separate purchase required.

5. Daily Maintenance & Standard Troubleshooting

5.1 Detailed Daily Maintenance Specifications

Point 1 Long-term Load Usage Standard

The turntable has separate rated load for step rotation and continuous rotation. For long-term stable operation, users should only load 80% of the maximum rated load value to reduce internal gear and motor abrasion, extend the whole machine service life, avoid long-term full-load running.

Point 2 Detailed Cleaning & Storage Requirements

• Wipe turntable surface and shutter port regularly with dry soft cloth;
• Store factory shutter cable set separately to avoid wire fracture caused by bending;
• Power off and store in dry ventilated area when idle.

5.2 Complete Common Troubleshooting Steps

Point 1 Turntable Cannot Power On

1. Check if power adapter DC plug is fully inserted into turntable power jack; 2. Check AC plug of adapter is fully inserted into wall socket with power supply; 3. Toggle the side power switch repeatedly between ON/OFF to confirm switch contact is intact.

Point 2 Remote Has No Control Response

1. Open remote battery compartment, replace two brand new AAA batteries;
2. Remove all obstacles between remote transmitting window and turntable infrared receiving window;
3. Keep remote within 5 meters of turntable and aim directly at receiving window to send control signals.

Point 3 USB Wired PC Connection Failed

• Uninstall and reinstall official CH340 driver, restart computer after installation;
• Replace intact standard USB Type-B cable, re-plug both ends tightly;
• Reopen Windows Device Manager to confirm valid COM port exists, re-select matching serial port in TurntableX and click Connect again.

Point 4 Mobile WiFi Cannot Connect Turntable Hotspot

• Confirm turntable power switch stays ON and wait 10s for hotspot broadcast;
• Turn mobile WLAN off and restart, refresh network list to reload turntable hotspot;
• Input correct default password 88889999 without extra space character when connecting hotspot.